MOULDING PROPERTIES OF SOME MALAYSIAN TIMBERS

Authors

K.S. Ho
Said Ahmad

Keywords:

Moulding properties, cutting angles, Malaysian timber

Abstract

Moulding properties of rubberwood,light red meranti, ramin and nyatoh were investigated with seven cutting angles starting from 150 to 45°. The surface quality and the occurrences of machining defects for each cutting angle are presented. The best cutting angle for each species is also determined.

Downloads

Download data is not yet available.

Downloads

PDF

Published

06-06-1991

Issue

Vol. 3 No. 4 (1991)

Section

Articles

How to Cite

MOULDING PROPERTIES OF SOME MALAYSIAN TIMBERS. (1991). JOURNAL OF TROPICAL FOREST SCIENCE, 3(4), 361-366. https://jtfs.frim.gov.my/jtfs/article/view/2070

Download Citation

Similar Articles

AW Mohd Jamil, J Mohd Zamin, MK Mohamad Omar, RELATIONSHIP BETWEEN MECHANICAL PROPERTIES OF STRUCTURAL SIZE AND SMALL CLEAR SPECIMENS OF TIMBER , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 25 No. 1 (2013)
AW Mohd Jamil, MK Mohamad Omar, STRENGTH AND STIFFNESS OF REMNANTS OF FRACTURED TIMBER , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 27 No. 1 (2015)
Mohd. Shahwahid Haji Othman, ECONOMIC IMPACT OF MALAYSIAN TIMBER EXPORTS , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 5 No. 1 (1992)
Roslan Ali, R. Amano, Said Ahmad, PLANING PROCESS OF MALAYSIAN TIMBERS 1. EFFECT OF VARIOUS CUTTING FACTORS ON PLANING QUALITY , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 3 No. 3 (1991)
SOA Saifulazry, MECHANICAL AND PHYSICAL PROPERTIES OF PARTICLEBOARD MADE FROM 4-YEAR-OLD RUBBERWOOD OF RRIM 2000 SERIES CLONES , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 22 No. 4 (2010)
P Edwin, B Ozarska, BENDING PROPERTIES OF HARDWOOD TIMBERS FROM SECONDARY FOREST IN PAPUA NEW GUINEA , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 27 No. 4 (2015)
WP Abasolo, PROPERTIES OF RATTAN CANE AS BASIS FOR DETERMINING OPTIMUM CUTTING CYCLE OF CULTIVATED CALAMUS MERRILLII , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 27 No. 2 (2015)
Murughan M, Mohamad Roslan MK, Zubaidah H, Johar M, Seca G, Pakhriazad HZ, DRIVERS FOR ADOPTING MALAYSIAN TIMBER CERTIFICATION SCHEME/PROGRAMME FOR THE ENDORSEMENT OF FOREST CERTIFICATION CHAIN OF CUSTODY CERTIFICATION IN MALAYSIA , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 36 No. 3 (2024)
AS Nordahlia, UMK Anwar, H Hamdan, A Zaidon, MK Mohamad Omar, MECHANICAL PROPERTIES OF 10-YEAR-OLD SENTANG (AZADIRACHTA EXCELSA) GROWN FROM VEGETATIVE PROPAGATION , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 26 No. 2 (2014)
MU Matsuo, KC Sujan, I Hirota, M Kojima, M Yoshida, H Yamamoto, UTILISATION OF STYRAX TONKINENSIS WOOD IN LAOS AND ITS PHYSICAL PROPERTIES , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 28 No. 3 (2016)

1-10 of 580 Next

You may also start an advanced similarity search for this article.

Most read articles by the same author(s)

Ahmad Shakri Mat Seman, Ashaari Hj. Amin, Hilmi Md. Tahir, Said Ahmad, SOME MECHANICAL AND ABRASIVE PROPERTIES OF PINANG SALAR (ARECA CATECHU) STEMS , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 6 No. 3 (1994)
W.C. Wong, K.S. Ho, C.N. Wong, ACACIA MANGIUM FROM SAB AH FOR PLYWOOD AND DECORATIVE PANEL MANUFACTURE: INITIAL TRIALS , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 1 No. 1 (1988)
Roslan Ali, M. Komatsu, Said Ahmad, PLANING PROCESS OF MALAYSIAN TIMBERS II. MECHANICAL EVALUATION OF HIGH SPEED STEEL (HSS) KNIFE EDGE WEAR IN PLANING SOME MALAYSIAN TIMBERS , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 4 No. 1 (1991)
Said Ahmad, Ashaari Haji Amin, Roslan Ali, Hilmi Md. Tahir, WITHDRAWAL AND BENDING STRENGTHS OF DOWELS FROM THREE MALAYSIAN TIMBERS , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 6 No. 1 (1993)
Roslan Ali, R. Amano, Said Ahmad, PLANING PROCESS OF MALAYSIAN TIMBERS 1. EFFECT OF VARIOUS CUTTING FACTORS ON PLANING QUALITY , JOURNAL OF TROPICAL FOREST SCIENCE: Vol. 3 No. 3 (1991)